Header Ads

Eleaf iStick Power User Manual

iStick Power

How to use?
Power on/off: Press the fire button 5 times in quick succession to turn on/off the device. Keep holding the fire button to take a puff when the device is powered on.

Stealth on/off: Press the fire button and down button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button one time to see current setting.

Adjustment buttons lock/unlock: Keep pressing up button and down button simultaneously for two seconds when the device is powered on, then the up and down buttons will be locked and the screen will display “Lock”. In the same way, the up and down buttons can be unlocked and the screen will display “Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan. 

Switch display mode: Keep pressing up button and down button simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation. 

Switch vaping modes: Long press the mode button to switch among VW, Bypass, Smart, TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes. 

1) In VW mode: When set in VW mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm.

Adjust wattage: In VW mode, the output wattage can be adjusted from 1W to 80W by pressing up button or down button, up button to increase and down button to decrease. Long press up button or down button can rapidly increase or decrease the wattage level. 

2)In Bypass mode: Direct output voltage system is applied in Bypass mode. The higher the battery level is, the higher the output voltage is. When set in this mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm. 

3)Smart mode: In Smart mode, the wattage can be adjusted from 1W to 80W by pressing up button or down button only when an atomizer is installed on the device. The Smart mode will save one output power setting for each resistance value and can totally save ten groups of such profiles. Once you change the output power setting for a resistance, it will re-save the changed setting automatically. When the Smart mode has already remembered ten profiles and you want to add another new resistance, the first saved profile will be deleted. When set in this mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm.

4)In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) Mode: When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and 316 Stainless Steel coils. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05ohm-1.5ohm) 

The Setting of TCR Mode (M1,M2,M3): When the device is powered off, keep pressing the fire button and the up button simultaneously, then you will enter into the TCR (M1,M2,M3) set menu: 
1. Press the up or down button to choose among M1, M2 and M3; 
2. Press the fire button one time to confirm the mode you chose;
3. Press the up or down button to increase or decrease the TCR value according to the material of the coil you used; 
4. Keep holding the fire button or stay in the interface for about 10 seconds to confirm your setting.

Following are different TCR value ranges for different coils for your reference:

Note: 1.The TCR value in the sheet is 10  multiplied of the actual TCR.           2.Our total range of TCR value is 1-1000. 

Adjust wattage: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, the output wattage can be adjusted from 1W to 80W. Keep pressing the mode button and up button simultaneously without looseness to increase the wattage level. On the contrary, keep pressing the mode button and down button simultaneously without looseness to decrease the wattage level. 

Adjust temperature: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Long press up button or down button can rapidly increase or decrease temperature setting. 

Shift between ℃ and ℉: If you increase the temperature to 315 ℃, and continue to press the up button, the temperature reading will automatically change to the lowest Fahrenheit (200℉). Equally, if the temperature is set at the lowest Fahrenheit (200℉) and you continue to press the down button, the temperature reading will automatically change to the highest Celsius (315 ℃). 

Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, keep pressing the fire button and up button simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked. 

Note: 
1. Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”. 
2. In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the down button and if it is a new coil, press the up button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance.
3. When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode by mistake, the device will automatically switch to VW mode. 

How to put custom logo in the Eleaf iStick Power mod? 
Download the file on our official website, plug the device in with USB cable, and double click the EleafUpdate.exe. Then click “LOGO” and open the image you choose to put it in the device. Finally press the fire button twice in quick succession when the device is powered on to enter logo on/off interface and press up or down button one time to turn on/off logo. 

Note: 
1. Please make sure the image you choose is a monochrome image of 96*16 pixel in the format of bmp. 
2. If you fail to put the custom logo in and the device shuts down, press the down button one time to restart the device. 

Properties 
Atomizer Protection: Each time when vaping time exceeds ten seconds, the output shuts off automatically with “Over 10s” display on the screen. 

Atomizer Short-circuit & No Atomizer Protection: When atomizer short-circuit occurs, the OLED screen will display “Atomizer Short”. The screen will display “No Atomizer” when there is no atomizer connected. 

Low-voltage Protection: When the voltage of the device is below 3.3V, the OLED screen will display “Lock” and the output will cut off automatically. Charge the device to reactivate it. 

Temperature Protection: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, when the actual temperature of coil reaches the set temperature, the screen will display "Temp Protection". 

Temperature Alert: If the temperature of device is over alert temperature, the output will shut off automatically and the screen will display “Device Too Hot”. You can continue to vape after it cools down. 


1 comment:

Powered by Blogger.